This is an outdated version published on 2022-08-31. Read the most recent version.

Industrial storage system continuous perforated uprights: a combined design proposal

Authors

  • Luiz Neiva Department of Construction and Structures, Federal University of Bahia, Bahia (Brazil)
  • Juliane Aparecida Braz Starlino Department of Civil Engineering, Federal University of Ouro Preto, Minas Gerais (Brazil)
  • Guilherme Elias Department of Civil Engineering, Federal University of Ouro Preto, Minas Gerais (Brazil)
  • Arlene Maria Cunha Sarmanho Department of Civil Engineering, Federal University of Ouro Preto, Minas Gerais (Brazil)
  • Vinícius Nicchio Alves Department of Civil Engineering, Federal University of Ouro Preto, Minas Gerais (Brazil)

DOI:

https://doi.org/10.7764/RDLC.21.2.204

Keywords:

industrial storage systems, rack, continuous perforations, cold-formed steel, compression members, buckling design curve

Abstract

Brazilian standards for design of cold-formed steel (ABNT NBR 14762:2010, 2010) and design of pallet racks (ABNT NBR 15524-2:2007, 2007) have different procedures to determine the strength of columns under axial compression, using different buckling curves. This paper aims to evaluate the efficiency of using cold-formed Brazilian standard buckling design curve instead of the formulations of the pallet-rack design standard to study the use viability of the equations in the calculation procedure for computing the uprights compressive strength. This strength was calculated in four ways: one using the original equations of pallet-rack Brazilian standard, and the other three using adaptations of the buckling curve from the cold-formed steel design standard. A theoretical and numerical procedure based on finite element analysis concerning local, global, and distortional buckling and imperfections was performed. Furthermore, experimental results were also consulted to determine the effective area of studied cross-sections considering the effects of local buckling and the presence of continuous perforations. The results show that the proposed modifications are consistently correlated to the results obtained using the original equations of ABNT NBR 15524, indicating the viability of using the buckling curve of ABNT NBR 14762.

Downloads

Download data is not yet available.

References

ABNT NBR 14762:2010. (2010). Dimensionamento de estruturas de aço constituídas por perfis formados a frio. Associação Brasileira de Normas Técni-cas.

ABNT NBR 15524-2:2007. (2007). Sistemas de armazenagem Parte 2: Diretrizes para o uso de estruturas tipo porta-paletes seletivos. Associação Brasileira de Normas Técnicas.

ANSYS Inc. (2012). ANSYS. ANSYS, Inc.

Baldassino, N., Bernuzzi, C., & Simoncelli, M. (2019). Evaluation of European approaches applied to design of TWCF steel members. Thin-Walled Struc-tures, 143, 106186. https://doi.org/10.1016/j.tws.2019.106186

Bernuzzi, C., & Simoncelli, M. (2017). EU and US design approaches for steel storage pallet racks with mono-symmetric cross-section uprights. Thin-Walled Structures, 113, 181–204. https://doi.org/10.1016/j.tws.2017.01.014

Bonada, J., Pastor, M. M., Roure, F., & Casafont, M. (2015). Influence of the cold work effects in perforated rack columns under pure compression load. Engineering Structures, 97, 130–139. https://doi.org/10.1016/j.engstruct.2015.04.011

Elias, G. C., Neiva, L. H. de A., Sarmanho, A. M. C., Alves, V. N., & Castro, A. F. B. (2018). Ultimate load of steel storage systems uprights. Engineering Structures, 170(May), 53–62. https://doi.org/10.1016/j.engstruct.2018.05.078

EN 15512. (2009). Steel static storage system —Adjustable pallet racking systems – Principles for structural design. European Standard. European Com-mitee for Standardization.

EN1993-1-3:2006. (2006). Eurocode 3: Design of steel structures - Part 1-3: General rules - Supplementary rules for cold-formed members and sheeting.

Huang, Z., Wang, Y., Zhao, X., & Sivakumaran, K. S. (2021). Determination of the flexural behavior of steel storage rack baseplate upright connections with eccentric anchor bolts. Thin-Walled Structures, 160, 107375. https://doi.org/10.1016/j.tws.2020.107375

Liu, S.-W., Pekoz, T., Gao, W.-L., Ziemian, R. D., & Crews, J. (2021). Frame analysis and design of industrial rack structures with perforated cold-formed steel columns. Thin-Walled Structures, 163, 107755. https://doi.org/10.1016/j.tws.2021.107755

Mecalux. (2020). Retrieved from https://www.mecalux.com.br/

Moen, C D, & Schafer, B. W. (2011). Direct Strength Method for Design of Cold-Formed Steel Columns with Holes. Journal of Structural Engineering, 137(5), 559–570. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000310

Moen, Cristopher D., & Schafer, B. W. (2009). Elastic buckling of thin plates with holes in compression or bending. Thin-Walled Structures, 47(12), 1597–1607. https://doi.org/10.1016/j.tws.2009.05.001

Moen, Cristopher D, & Schafer, B. W. (2009). Elastic buckling of cold-formed steel columns and beams with holes. Engineering Structures, 31(12), 2812–2824. https://doi.org/10.1016/j.engstruct.2009.07.007

Neiva, L. H. de A., Sarmanho, A. M. C., Faria, V. O., Souza, F. T. de, & Starlino, J. A. B. (2018). Numerical and experimental analysis of perforated rack members under compression. Thin-Walled Structures, 130(February), 176–193. https://doi.org/10.1016/j.tws.2018.05.024

Pastor, M. M., Bonada, J., Roure, F., & Casafont, M. (2013). Residual stresses and initial imperfections in non-linear analysis. Engineering Structures, 46, 493–507. https://doi.org/10.1016/j.engstruct.2012.08.013

Pierin, I., & Pignatta, V. (2015). Distortional buckling resistance of cold ‑ formed steel. Journal of the Brazilian Society of Mechanical Sciences and Engi-neering, 1163–1171. https://doi.org/10.1007/s40430-014-0252-x

Prabha, P., Marimuthu, V., Saravanan, M., & Arul Jayachandran, S. (2010). Evaluation of connection flexibility in cold formed steel racks. Journal of Constructional Steel Research, 66(7), 863–872. https://doi.org/10.1016/j.jcsr.2010.01.019

Ribeiro, F. S. (2006). Análise teórico-expeimental de colunas curtas em perfis formados a frio de seção transversal tipo rack. Master Dissertation, Vitória: Universidade Federal do Espírito Santo.

Sena Cardoso, F., & Rasmussen, K. J. R. (2016). Finite element (FE) modelling of storage rack frames. Journal of Constructional Steel Research, 126, 1–14. https://doi.org/10.1016/j.jcsr.2016.06.015

Silva, L. S.; Simões, R.; Gervásio, H.; Vellasco, P.; Lima, L. (2016). Dimensionamento de Estruturas de Aço: Comparação entre o Eurocódigo 3 e a Norma Brasileira NBR8800 (1a Edição).

Specification, N. A., & Members, S. S. (2016). North American Specification for the Design of Cold-Formed Steel Structural AISI S100-16.

Thasan, S., & Rajendran, S. (2020). Cold formed steel storage racks subjected to axial, shear and bending interactions. Revista de La Construccion. https://doi.org/10.7764/RDLC.19.2.306

Downloads

Published

2022-08-31 — Updated on 2022-08-31

Versions

How to Cite

Neiva, L., Braz Starlino, J. A. ., Elias, G., Cunha Sarmanho, A. M. ., & Nicchio Alves, V. . (2022). Industrial storage system continuous perforated uprights: a combined design proposal. Revista De La Construcción. Journal of Construction, 21(2), 204–214. https://doi.org/10.7764/RDLC.21.2.204